Huanggang Rebar Waste Treatment Truncation Recycling Reuse JT50 Waste Rebar Cut-off Machine Helps Users Make Money

2021-05-23

JT50 type waste steel cutting machine is now the steel recycling business. The user loves the equipment to do the steel scrap waste treatment and cut recycling equipment. The JT50 type waste steel cutting machine cuts the steel section to make the steel mill better dissolve and save energy when it returns to the furnace!

Convenient transportation, so users recycle waste steel bars more than cut off per ton. It is a good equipment to help users make money. Users who need JT50 waste steel cutting machine to make money can call Kang Manager to learn more about the price performance of JT50 waste steel cutting machine. And use!



Precautions for the operation of the steel bar cutting machine: The first thing to note is that the work surface of the steel bar cutting machine should be kept horizontal with the lower part of the cutter so that the steel bar can be cut better. Before starting the steel bar cutting machine, it is necessary to check whether the parts are in the specified position, whether there is any wear and tear, and if so, replace it as soon as possible. After the start, it should be operated first, check that the transmission parts and bearings are running normally before they can work. Otherwise, if there are impurities between the parts, it will hinder the mechanical operation and cause machine failure. The steel bar cutting machine shall not cut the steel bars and the red-hot steel bars whose diameter and strength exceed the mechanical nameplate. This requires strict operation, and when cutting multiple steel bars at one time, the total diameter of the steel bars shall not exceed the specified standard size. It should be noted that during the operation, no unrelated personnel should bring the hand or sundries close to the steel bar cutting machine to avoid accidental injury.
If there is a problem during the operation of the steel cutter, such as abnormal mechanical operation, abnormal noise or skew of the cutter, immediately turn off the power for troubleshooting and timely maintenance. When the operation of the steel bar cutting machine is completed, the power should be cut off immediately, then use the steel brush to remove the debris between the cutters, clean and lubricate the machine, and wait until all the operation stops before leaving. During these operations, workers must wear insulated gloves, which is the most important.
Many people don't know how to operate the steel cutting machine in the past. They always make a lot of misunderstandings according to their own ideas. This is not only a threat to their own safety but also easy to cause mechanical damage. It is best to operate according to the correct method. . Guarantee your own safety, extend the mechanical operation life, and avoid the damage caused by multiple repairs. Only when the operation is correct, can you work better. The correct method of operation is not only the respect for the steel cutter, but also the responsibility for your own life.



The waste steel bar cutting machine has less function loss, and the gear end is improved due to the improvement of lubrication conditions.
The scrap steel cutting machine adopts a rolling bearing and has low resistance. Compared with the same type of cutting machine, the power consumption can be greatly reduced under load. The waste steel cutting machine adopts high-strength steel seat, connecting rod and high-speed national standard motor, which has more stable quality and longer service life.
The main features of the scrap steel cutting machine: the reinforced fuselage, small size, compact structure, solid and reliable. Double-head cutting, high efficiency, large output, eliminating most of the labor. It has good lubrication performance, adopts closed structure, utilizes gear splash lubrication, and adds 8KG of gear oil at a time, which can work continuously for two months.
Less loss of function: Due to the improvement of lubrication conditions, the gear end adopts rolling bearing, the resistance is small, and the power can be reduced by one third compared with the same type of cutting machine.
Easy to move: flexible and easy to maintain: The steel cutting machine is a special equipment developed by our company for the short section of the steel bar. It is mainly used for the processing before the waste is returned to the furnace.
Composition: The steel cutting machine consists of an electric motor, a gearbox, a reducer, a steel discharge port, and a fuselage.
Operation principle: The steel bar cutting machine is driven by the motor to drive the speed reducer to rotate, and then the speed reducer runs through the sprocket drive gearbox to keep the cutter working continuously, so as to cut the steel bar.








Http://news.chinawj.com.cn

3 phase rebar cutting machine, this machine should be 3phase 380V/220V/440V. The motor should be confirmed as customer's local requirement.

rebar cutting machine also can apply single phase as customer's requirement.

3phase rebar cutting machine can be applied to cut the normal common carbon steel rod, hot rolled steel, deformed steel, flat steel, square steel, and angle steel in machine processing and construction projects.

 

Rebar Cutting Machine, Electric Rebar Iron Cutting Machine, Circular Saw Rebar Cutting Machine, Cheap Rebar Cutting Machines
Hvcen Machinery Technology Co., Ltd. http://www.rebarconnectors.com